// ---------------------------------------- // // The following SmartCAM code generator has been // created to generate NC code for the respective // machine and control combinations listed below. // // Due to differences in programming styles, // controller versions, and optional equipment, // SmartCAMcnc DOES NOT and CANNOT guarantee // that the NC code generated is correct for any // specific machine. Some modification to the code // generator to match your setup and output // requirements is likely necessary. // // Modifications to code generators do not TYPICALLY // require a significant amount of time. SmartCAM // customers with active SSA contracts are entitled // to support for their code generators from the // SmartCAMcnc Support Group. To contact them for // support, please send an email to: // Support@SmartCAMcnc.com. If you would like // information on purchasing SSA for your SmartCAM // products, please contact: Sales@SmartCAMcnc.com // // DISCLAIMER: It is the responsibility of the end // user to confirm and verify that the NC code // created by any code generator is accurate and // will not cause a machine malfunction which // could result in stock, tooling, machine, and/or // personal injury. // // SmartCAMcnc assumes no responsibility or // liability for any damage caused or alleged to // have been caused by the use of any of the code // generators it provides. // ---------------------------------------- EXELCENTER 4,4L,4XL 30.11.87 BIEDERMANN ROKKU-ROKKU VERTIMAC C,F,K,G ----------------------------------------------------------------------------- FA.BAILER ----------------------------------------------------------------------------- @START % #ONBLK M98 P100 S#SPEED F#FEED #SPNDL T#NTOOL G54 #MOV X#XPOS Y#YPOS G43 Z#ZPOS H#LOFF M08 @TOOLCHG < #FXD> M98 P1000 #SAFBLK M98 P100 S#SPEED F#FEED #SPNDL T#NTOOL G54 #MOV X#XPOS Y#YPOS G43 H#LOFF Z#ZPOS M08 @END M98 P1000 G28 G91 Y0 M30 #OFFBLK% @STPROF < #FXD>< #MOV>< X#XPOS>< Y#YPOS>< Z#ZPOS> @ENDPROF #MOV Z#ZPOS < #DCOMP> @RAP < #FXD>< #MOV>< X#XPOS>< Y#YPOS>< Z#ZPOS> @LINE < #DCOMP D#DOFF>< #MOV>< X#XPOS>< Y#YPOS>< Z#ZPOS>< F#FEED> @ARC < #MOV>< X#XPOS>< Y#YPOS>< I#XCTR>< J#YCTR>< F#FEED> @ZCLRMV < #FXD>< #MOV>< Z#ZPOS> @ZCHKMV < #FXD>< #MOV>< Z#ZPOS> @ZDPTHMV < #MOV>< Z#ZPOS>< F#FEED> @FXD1 < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> @FXD2 < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK P#DWELL>< F#FEED> @FXD3 #EVAL(#ZCHK=#ZCHK+4) < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> @FXD4 < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> @FXD5 < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK Q#PECK>< F#FEED> @