// ---------------------------------------- // // The following SmartCAM code generator has been // created to generate NC code for the respective // machine and control combinations listed below. // // Due to differences in programming styles, // controller versions, and optional equipment, // SmartCAMcnc DOES NOT and CANNOT guarantee // that the NC code generated is correct for any // specific machine. Some modification to the code // generator to match your setup and output // requirements is likely necessary. // // Modifications to code generators do not TYPICALLY // require a significant amount of time. SmartCAM // customers with active SSA contracts are entitled // to support for their code generators from the // SmartCAMcnc Support Group. To contact them for // support, please send an email to: // Support@SmartCAMcnc.com. If you would like // information on purchasing SSA for your SmartCAM // products, please contact: Sales@SmartCAMcnc.com // // DISCLAIMER: It is the responsibility of the end // user to confirm and verify that the NC code // created by any code generator is accurate and // will not cause a machine malfunction which // could result in stock, tooling, machine, and/or // personal injury. // // SmartCAMcnc assumes no responsibility or // liability for any damage caused or alleged to // have been caused by the use of any of the code // generators it provides. // ---------------------------------------- MATRA MIT FANUC 0M 20.04.89 ----------------------------------------------------------------------------- @START % #ONBLK G00 G91 G28 Z0 T#TOOL M6 #TLCMT G90 #MOV X#XPOS Y#YPOS S#SPEED F#FEED #SPNDL G43 Z#ZPOS H#LOFF M08 @TOOLCHG #RESET(#FXD) (WKZG-ZEIT WKZG #LTOOL #TLTIME) G00 G91 G28 Z0 M9 M5 T#TOOL M6 #TLCMT G90 #MOV X#XPOS Y#YPOS S#SPEED F#FEED #SPNDL G43 H#LOFF Z#ZPOS M08 @END (WKZG-ZEIT WKZG #LTOOL #TLTIME) (GESAMTZEIT #CYTIME) G28 G91 Z0 M9 G28 G91 Y0 M5 M30 #OFFBLK% @STPROF < #FXD>< #MOV>< X#XPOS>< Y#YPOS> @ENDPROF < #MOV>< Z#ZPOS> < #DCOMP> @RAP < #FXD>< #MOV>< X#XPOS>< Y#YPOS> @LINE < #DCOMP H#DOFF>< #MOV>< X#XPOS>< Y#YPOS>< Z#ZPOS>< F#FEED> @ARC < #MOV>< X#XPOS>< Y#YPOS>< I#XCTR>< J#YCTR>< F#FEED> @ZCLRMV < #FXD>< #MOV>< Z#ZPOS> @ZCHKMV < #FXD>< #MOV>< Z#ZPOS> @ZDPTHMV < #MOV>< Z#ZPOS>< F#FEED> @FXD1 < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> @FXD2 < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK P#DWELL>< F#FEED> @FXD3 #EVAL(#V9=#ZCHK+2) < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#V9>< F#FEED> @FXD4 < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> @FXD5 < #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK Q#PECK>< F#FEED> @ROTATE G80 G00 Z#ZPOS B#V0 #RESET(#FXD Z#ZDPTH)< F#FEED> @PLCHNG M98P100 M#V1 @NULL G#V2 @