// ---------------------------------------- // // The following SmartCAM code generator has been // created to generate NC code for the respective // machine and control combinations listed below. // // Due to differences in programming styles, // controller versions, and optional equipment, // SmartCAMcnc DOES NOT and CANNOT guarantee // that the NC code generated is correct for any // specific machine. Some modification to the code // generator to match your setup and output // requirements is likely necessary. // // Modifications to code generators do not TYPICALLY // require a significant amount of time. SmartCAM // customers with active SSA contracts are entitled // to support for their code generators from the // SmartCAMcnc Support Group. To contact them for // support, please send an email to: // Support@SmartCAMcnc.com. If you would like // information on purchasing SSA for your SmartCAM // products, please contact: Sales@SmartCAMcnc.com // // DISCLAIMER: It is the responsibility of the end // user to confirm and verify that the NC code // created by any code generator is accurate and // will not cause a machine malfunction which // could result in stock, tooling, machine, and/or // personal injury. // // SmartCAMcnc assumes no responsibility or // liability for any damage caused or alleged to // have been caused by the use of any of the code // generators it provides. // ---------------------------------------- //Machine: Shoda four spindle router //Control: Shoda //Date: April 27, 1990 @START % O#S0 (#DATE) (PC FILE=#FILE) (#TLID #TLCMT CUTTER COMP = D#DOFF) (PROG BY CRS) #ONBLK G54 G40 G90 G17 G64 #TLID #TLCMT S#SPEED #MOV X#XPOS Y#YPOS Z#ZPOS T#TOOL #SPNDL @TOOLCHG #MOV G54 G28 Z0 #SPOFF #TLID #TLCMT S#SPEED< #C0> (#TLID #TLCMT CUTTER COMP = D#DOFF) T#TOOL #SPNDL Z#ZPOS @END G54 G28 Z0.0 #SPOFF< #C0> G28 X0.0 M30 #OFFBLK% @STPROF < #ABSI>< #MOV>< X#XPOS>< Y#YPOS> @ENDPROF #MOV Z#ZPOS < #DCOMP> @RAP < #ABSI>< #MOV>< X#XPOS>< Y#YPOS> @LINE < #DCOMP#EXC D#DOFF>< #MOV>< G#S1>< X#XPOS>< Y#YPOS>< Z#ZPOS>< F#FEED> @ARC < #MOV>< G#S1>< X#XPOS>< Y#YPOS>< I#XCTR>< J#YCTR>< F#FEED> @ZCLRMV < #ABSI><< #MOV> Z#ZPOS> @ZCHKMV < #FXD><< #MOV> Z#ZPOS> @ZDPTHMV << #MOV> Z#ZPOS< F#FEED>> @FXD1 < #ABSI>< #RTNLVL>< #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> @FXD2 < #ABSI>< #RTNLVL>< #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK P#DWELL>< F#FEED> @FXD3 < #ABSI>< #RTNLVL>< #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> @FXD4 < #ABSI>< #RTNLVL>< #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK>< F#FEED> @FXD5 < #ABSI>< #RTNLVL>< #FXD>< X#XPOS>< Y#YPOS>< Z#ZDPTH R#ZCHK Q#PECK>< F#FEED> @DWELL G04 X#DWELL @PCHANGE G54 G28 Z0.0 G28 X0.0 M39 @GOSUB M98 P#S3 @