//    ----------------------------------------
//    
//    The following SmartCAM code generator has been 
//    created to generate NC code for the respective 
//    machine and control combinations listed below. 
//    
//    Due to differences in programming styles, 
//    controller versions, and optional equipment, 
//    SmartCAMcnc DOES NOT and CANNOT guarantee
//    that the NC code generated is correct for any 
//    specific machine. Some modification to the code 
//    generator to match your setup and output 
//    requirements is likely necessary. 
//    
//    Modifications to code generators do not TYPICALLY
//    require a significant amount of time. SmartCAM 
//    customers with active SMA contracts are entitled 
//    to support for their code generators from the 
//    SmartCAMcnc Support Group. To contact them for 
//    support, please send an email to: 
//    Support@SmartCAMcnc.com. If you would like 
//    information on purchasing SMA for your SmartCAM 
//    products, please contact: Sales@SmartCAMcnc.com
//    
//    DISCLAIMER: It is the responsibility of the end 
//    user to confirm and verify that the NC code 
//    created by any code generator is accurate and 
//    will not cause a machine malfunction which 
//    could result in stock, tooling, machine, and/or 
//    personal injury. 
//    
//    SmartCAMcnc assumes no responsibility or 
//    liability for any damage caused or alleged to 
//    have been caused by the use of any of the code 
//    generators it provides.
//    ----------------------------------------

@START
\\ ** D&M 6 CNC MILL **
\\ #FILE
\\ #DATE
G70
G00
X1. Y3. Z2. RAPID ABS
M06 #TOOL
M07 #FEED
M04 #SPEED
Z#ZPOS RAPID ABS
@TOOLCHG
#MOV
X1. Y3. Z2. RAPID ABS
M06 #TOOL
M07 #FEED
M04 #SPEED
Z#ZPOS RAPID ABS
@END
G00
X1. Y3. Z2. RAPID ABS
M06 0
M04 0
X0 Y0 Z1 RAPID ABS
M30
@STPROF
<#MOV>
<X#XPOS>< Y#YPOS>< Z#ZPOS> RAPID ABS
@ENDPROF
<#MOV>
<X#XPOS>< Y#YPOS>< Z#ZPOS> RAPID ABS
@RAP
<#MOV>
<X#XPOS>< Y#YPOS>< Z#ZPOS> RAPID ABS
@ZDPTHMV
M07 #FEED
Z#ZPOS FEED ABS
@LINE
<M07 #FEED>
<#MOV>
<X#XPOS>< Y#YPOS>< Z#ZPOS> FEED ABS
@ARC
<M07 #FEED>
<#MOV>
X#XCTR Y#YCTR FEED ABS
X#XPOS Y#YPOS FEED ABS
@ZCLRMV
<#MOV>
Z#ZPOS RAPID ABS
@ZCHKMV
<#MOV>
Z#ZPOS RAPID ABS
@FXD1
< #FXD>
X#XPOS Y#YPOS Z#ZDPTH FEED ABS
@FXD2
#FXD
X#XPOS Y#YPOS Z#ZDPTH FEED ABS
G80
@FXD3
@FXD4
< #FXD>
X#XPOS Y#YPOS Z#ZDPTH FEED ABS
G80
@FXD5
< #FXD>< 0 #PECK>
X#XPOS Y#YPOS Z#ZDPTH FEED ABS
@DWELL
G04 #EVAL(#TIME=#DWELL/60)
@